Type: disk
Protocol: SATA 3.1, 6.0 Gb/s (current: 6
Model: SAMSUNG MZ7KM480HAHP-00005
Family: Samsung based SSDs
Serial: S2HSNYAG500156
R Rate: SSD
Size Smart: 480 GB
Size: 447.1
Firmware: GXM1003Q
Active: 1

smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.15.0-20-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family: Samsung based SSDs
Device Model: SAMSUNG MZ7KM480HAHP-00005
Serial Number: S2HSNYAG500156
LU WWN Device Id: 5 002538 c000177b6
Firmware Version: GXM1003Q
User Capacity: 480,103,981,056 bytes [480 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4c
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Sat Sep 15 00:12:11 2018 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x02) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 2100) seconds.
Offline data collection
capabilities: (0x53) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 35) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.

SMART Attributes Data Structure revision number: 1
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0
9 Power_On_Hours 0x0032 095 095 000 Old_age Always - 22373
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 10
177 Wear_Leveling_Count 0x0013 099 099 005 Pre-fail Always - 33
179 Used_Rsvd_Blk_Cnt_Tot 0x0013 100 100 010 Pre-fail Always - 0
180 Unused_Rsvd_Blk_Cnt_Tot 0x0013 100 100 010 Pre-fail Always - 3788
181 Program_Fail_Cnt_Total 0x0032 100 100 010 Old_age Always - 0
182 Erase_Fail_Count_Total 0x0032 100 100 010 Old_age Always - 0
183 Runtime_Bad_Block 0x0013 100 100 010 Pre-fail Always - 0
184 End-to-End_Error 0x0033 100 100 097 Pre-fail Always - 0
187 Uncorrectable_Error_Cnt 0x0032 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0032 066 064 000 Old_age Always - 34
195 ECC_Error_Rate 0x001a 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 0
199 CRC_Error_Count 0x003e 100 100 000 Old_age Always - 0
202 Exception_Mode_Status 0x0033 100 100 010 Pre-fail Always - 0
235 POR_Recovery_Count 0x0012 099 099 000 Old_age Always - 7
241 Total_LBAs_Written 0x0032 099 099 000 Old_age Always - 23184298601
242 Total_LBAs_Read 0x0032 099 099 000 Old_age Always - 86930999200
243 SATA_Downshift_Ct 0x0032 100 100 000 Old_age Always - 0
244 Thermal_Throttle_St 0x0032 100 100 000 Old_age Always - 0
245 Timed_Workld_Media_Wear 0x0032 100 100 000 Old_age Always - 65535
246 Timed_Workld_RdWr_Ratio 0x0032 100 100 000 Old_age Always - 65535
247 Timed_Workld_Timer 0x0032 100 100 000 Old_age Always - 65535
251 NAND_Writes 0x0032 100 100 000 Old_age Always - 57628978184

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
255 0 65535 Read_scanning was completed without error
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.